Correct Replacement Bearing Kit for Casita Spirit Deluxe Trailer with 2,200 Lb Axle

Question

Question:

Hi, I have a 1996 Casita SD camper I need to replace the bearings. Documentations says its a Dexter Torsion 2200lb axle. What bearing kit do I need for this camper? Is it a BK1-150?

asked by: Matthew

0

Expert Reply:

The Bearing Kit, L44649 Inner/Outer Bearings part # BK1-150 is designed for 2,200 lb axles with a 1.063" bearing diameter so if this is what you have then it will be a great fit.

expert reply by: Conner L

0

Answer 1

While we don't have exact replacement parts or a way to figure out what fits the specs of your Long Chih Industrial LCI-850T trailer, we should still be able to help you out. All you'll need to do is take some measurements to ensure that you…

view full answer...

Answer 2

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 3

Based on your seal dimension being 1.5 inch and your bearing dimension of 1.06 inch on your spindle the correct bearing kit you need is the part #BK1-150.

view full answer...

Answer 4

Trailer makers unfortunately do not usually maintain records of the smaller components parts such as bearings that are used in the manufacture of their trailers but we do carry a broad assortment of replacement bearings, races and grease seals shown…

view full answer...

Answer 5

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 6

We have a few bearing kits that could potentially work for your utility trailer, but we first need to determine what you have on your trailer so that we can pick out the correct parts. What you would need to do is remove a current hub and get the…

view full answer...

Answer 7

Yes, that would be fine. We don't have any 73 inch axles though. Just a 72 inch like the part #20545I-EZ-72-10 which has a distance of 58 inches between the spring seats. If the spring seat dimension matches your trailer perfectly this would work…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

We have the grease seal you are looking for. Our part number #GS-2250DL is the same as the Dexter 010-054-00 that you have. The inner diameter of this seal is 2.25 and the outer is 3.376 inches.

view full answer...

Answer 10

The correct replacement hub for your 2005 Karavan KKR-1800-70 is the Easy Grease Trailer Idler Hub Assembly part #AKIHUB-545-2-G-EZ-2K. This hub has a galvanized finish which is best for saltwater and it comes with bearings, races, seal, and grease…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Correct Replacement Bearing Kit for Casita Spirit Deluxe Trailer with 2,200 Lb Axle

Product Page this Question was Asked From

Continue Researching