Warranty Coverage of Stromberg Carlson JET-5000 Powered Trailer Tongue Jack

Question

Question:

What is the warranty on this product? I recently purchased it and curious if I need to submit something for registration

asked by: Keith S

0

Expert Reply:

The Stromberg Carlson # JET-5000 is covered by a 2-year warranty.

If you purchased it from us, you won't need to do anything as we have you in our system. If you purchased it elsewhere, you'll need to check with that retailer to determine what their warranty service requirements are.

expert reply by: Mike L

0

Answer 1

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 2

I am sorry to hear about the functional issues you are having with your Stromberg Carlson Electric Trailer Jack #JET-3755. Based on the issue you are describing I would first manually lower the jack a little bit to make sure it was not overextended.…

view full answer...

Answer 3

Have you tried seeing if your cigarette lighter auxiliary plugs on your truck are still active? That power circuit is often times the same power circuit for the OBDII connections and when it fails programmers won't power on.

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Warranty Coverage of Stromberg Carlson JET-5000 Powered Trailer Tongue Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching