Solution for 7-Way of 1999 Ford F-250 With Running Light Circuit Not Active

Question

Question:

I have a 1999 f250 extended cab.short bed diesel I have lost my running light on my trailer plug Any suggestion All fuses and relays are good

asked by: Frank H

0

Expert Reply:

The most likely culprit is dirty pins on your trailer wiring connector. Try taking sandpaper to the pins to clean off any dirt and corrosion and see if that fixes the problem. You might find that the 7-way is damaged beyond repair and in that case you could easily replace it with the part # PK11893.

expert reply by: Jameson C

0

Answer 1

I don't see why they would be different. Especially if you find the same colors on your trailer wiring. You can verify this with a circuit tester like part #PTW2993 to be sure. I also attached 7-way diagrams you can compare the pin outs to as…

view full answer...

Answer 2

Thanks for the picture. In the picture of the vehicle end connector it is showing that the center pin has fallen out and will need to be replaced. For a replacement you will need either the Pollak Black Plastic, 7-Pole, RV Blade-Style Trailer Socket…

view full answer...

Answer 3

If just the taillights on your trailer are not working, but the turn signals and brake lights are you will want to start with finding if the issue is on the tow vehicle or trailer. Using a circuit tester like #PTW2993 test the 11 o'clock pin if…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 7

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 8

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 11

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Solution for 7-Way of 1999 Ford F-250 With Running Light Circuit Not Active

Product Page this Question was Asked From

Continue Researching