Will CE Smith Bunk Guide Ons CE27600 Fit Trailer Frames that are 1.5 inch Wide by 3 inch Tall

Question

Question:

Hello- Will the CE Smith Bunk-Style Guide-Ons, Item # CE27600, fit trailer frames of 1.5 wide and 3 tall?

asked by: Carlos N

0

Expert Reply:

Yes, the CE Smith Bunk-Style Guide-Ons # CE27600 does fit trailer frames that are 1-1/2 inch wide by 3 inches tall.

expert reply by: Jameson C

0

Answer 1

Absolutely. We have the Fulton Single Axle Trailer Fender with Top Step - Black Plastic - 14" Wheels - Qty 1 #F008554 which is 9-11/16" Wide x 31-5/16" long x 12-3/4" tall. This will work well for your tire size.

view full answer...

Answer 2

The CE Smith Bunk Style Guide Ons part #CE27600 are only available with the pre-galvanized steel finish. You could very easily paint them black with some spray paint though. Have to clean the surface first. Then prime it with non-petroleum primer…

view full answer...

Answer 3

The CE Smith Bunk-Style Guide-Ons #CE27600 that you referenced will help you line your boat up on your trailer in windy conditions. As long as you aren't slamming into them they won't bend and will work well. The arms are made of…

view full answer...

Answer 4

You can install the Bunk-Style Guide-Ons #CE27600 with a bit of modification to fit your 1 inch wide by 3 inches tall trailer. The guide-on is designed to fit a trailer with a minimum of a 2 inch width, with that being said, the modification that…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...