Replacement Bearings for Hayes 5,200 lb. Axle

Question

Question:

Do you carry Hayes 5 ton axle bearings? These have hydraulic disk brakes if that matters.

asked by: William M

0

Expert Reply:

We do not have bearings for a 5 ton rated axle but for the Hayes T52 5,200 lb. axle, which sometimes is listed at 5K rating, I recommend the Bearing Kit for Trailer Brakes with 12" Hub/Rotor - 5,200 lbs. to 6,000 lbs. # DBRKHW6.

expert reply by: Michael R

0

Answer 1

Most likely we have replacement assemblies but the individual parts will be dependent on the brand and numbers you find on the brake assemblies themselves as they are commonly swapped out for different brands. The assemblies are all interchangeable…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Replacement Bearings for Hayes 5,200 lb. Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching