Diameter of Bolt Holes of Square Corner T-Strap Hinge # PLR2212-AS

Question

Question:

Can you tell me what size the door hinge bolts are

asked by: Frederick A

0

Expert Reply:

The door hinge bolt hold diameters of the Polar Hardware # PLR2212-AS are 3/8 inch.

expert reply by: Jameson C

0

Answer 1

I attached a picture I got from Buyers Products that has the dimensions of the Buyers Products Hook and Keeper for Enclosed Trailer Door #BP64FR that has the dimensions you are looking for.

view full answer...

Answer 2

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will fit…

view full answer...

Answer 3

The eZ latch of the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors, eZ-Latch - 2-5/16" Ball - 21K #DM16680-52 is absolutely just as safe as a slide lock coupler. It doesn't use a pin but still exceeds the SAE J684 safety…

view full answer...

Answer 4

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

view full answer...

Answer 5

You could drill into the Bulldog #BD028463 and make it a bolt-on but that's not really ideal. We don't have the exact match in a bolt-on model. We do have part #BD44150WH301 for a bolt-on Bulldog coupler. It has a higher rating but the price…

view full answer...

Answer 6

looking at all the options we have for 2-5/16 inch A-Frame Couplers, the one you're looking at #DM16680-52 seems to look the most similar. I don't see any coupler that will be a perfect replacement. The holes on our coupler seem smaller and…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Diameter of Bolt Holes of Square Corner T-Strap Hinge # PLR2212-AS

Product Page this Question was Asked From

Continue Researching