Overall Height of 2.5" Curt Adjustable 2-Ball Channel Mount While At Lowest Setting

Question

Question:

I’m trying to find the overall length but am not having any luck. More importantly, need the distance from the bottom or top of the shank to the bottom of the , when in the 10-3/8” position. Can you help please? Thank you!!

asked by: Gary K

1

Helpful Expert Reply:

The distance from the top of the shank to the bottom of the hitch ball at the lowest setting on the Curt Adjustable 2-Ball Channel Mount part # C45927 is 14-3/8". I went out to our warehouse to measure this for you.

expert reply by: Conner L

1

Overall Height of 2.5" Curt Adjustable 2-Ball Channel Mount While At Lowest Setting
(click to enlarge)

Answer 1

The Replacement 10K Ball Mount Tongue for Brophy Adjustable Drop Hitch #RTB1 will not fit the Curt Weight Distribution Shank for 2-1/2" Hitches #C17131 as #RTB1 only fits Brophy Shanks. Instead, what will work with the Curt WD Shank #C17131 is…

view full answer...

Answer 2

I have a solution for you but there is no way to purchase just the ball mount portion of the Curt Channel Style Adjustable Ballmount - 5-1/4" Rise, 6-3/4" Drop - 6,000 lbs item #C45901. You can however use the Replacement 2" and…

view full answer...

Answer 3

For your Curt Adjustable Ball Mount part #C45900 you'd have to stick with using the Curt dual sided hitch ball part #C45912 as the part #RTB1 only fits a Brophy shank.

view full answer...

Answer 4

The Buyers Products 3-Position Adjustable Lunette Ring with 3" Heavy-Duty Channel #337B20143 will fit correctly with a Curt Pintle Hook with 2-5/16" Ball #C45908.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 11

I would love to help but I can't really tell you if you need the B&W Tow & Stow 2-Ball Mount with 5" Drop part #BWTS20037B (part #BWTS20037C) or 7" Drop part #BWTS20040B (part #BWTS20040C) as it varies by application so you will…

view full answer...

Answer 12

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Overall Height of 2.5" Curt Adjustable 2-Ball Channel Mount While At Lowest Setting

Product Page this Question was Asked From

Continue Researching