Additional Stability and Sag Prevention With TorkL

Question

Question:

Hello wondering about your stability plus keeper spring we have a 2019 GMC 2500 with torque lift stable loads installed can both systems be used together right now with the stable loads installed the rear ones still won’t engage when not hauling and sags when we do

asked by: Steve B

0

Expert Reply:

I recommend adding the SuperSprings Custom Suspension Stabilizer and Sway Control Kit # SSA13MXKT on your 2019 GMC Sierra 2500 as you already have the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect # TLA7310S.

expert reply by: Bud M

0

TorkLift StableLoad Installed On a 2019 GMC Sierra 2500
(click to enlarge)

Answer 1

Hi Richard! It sounds like you're needing to install the Load Resistor Kit for LED Turn Signals #DI34ZR on the turn signals you've installed on your toolbox. Since LEDs don't require as much power as incandescent bulbs,…

view full answer...

Answer 2

I can only help you pick out the best psi but I can't tell you off-hand exactly the best pressure to use. What you want to do is put in an equal amount of pressure in both bags till the truck is sitting as close to stock ride height as it…

view full answer...

Answer 3

While the spacers included in the Kit #T68MR will work with your Timbren Springs #TGMRYS4 they do not use the same mounting bolts. Your GMC Yukon uses 3/8" hardware while the spacer kit includes M10 hardware so you would still need to source…

view full answer...

Answer 4

We offer the Reese 9485 as our own unique part number, #DT89MR, as well as the Curt #C60633 or the B&W #BWGNRK1320 which will all fit. If I personally had to choose between the two, I'd go with the B&W because I prefer the…

view full answer...

Answer 5

I can help but unfortunately, I can't really give you an exact psi to tow your 3,500 lb - 4,000 lb trailer as there are just too many factors that go into selecting the correct air pressure. The most important of which however is ride…

view full answer...

Answer 6

The Replacement Rung for Stromberg Carlson RV Exterior Ladder measures 13-1/4" overall length. The diameter of the hole is 1". From the center of one of the holes to the other hole is 11-1/4" and the measurement between the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

There are a couple of things that set the Rhino Rack system using #RRVA150B-2, #RRRCH4, #RRRCP43-BK apart from the Inno system that uses parts #INXB138-2, #INXS350, #INTR154 you're looking at. I'll start out by saying that when it comes to…

view full answer...

Answer 11

Both the Rhino-Rack Vortex Aero and Thule WingBar roof rack systems have very nice features and would work well for your 2014 Hyundai Santa Fe. Both systems are designed to work on vehicles that have the flush mounted rail system. As far as the…

view full answer...

Additional Stability and Sag Prevention With TorkL

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching