Will Ark Ezi-Guides Self-Aligning Boat Trailer Loading System Non-Scuffing

Question

Question:

Do the rollers on these guides leave scuff marks?

asked by: Karl S

0

Expert Reply:

The rollers of the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System # AR64FR will not leave scuff marks.

expert reply by: Jameson C

0

Answer 1

The Ark Ezi-Guides Self-Aligning Boat Trailer Loading System part #AR64FR are indeed spring loaded so they will swing down once the weight of the boat passes over them. They are designed to be installed closer to the rear per the instructions. The…

view full answer...

Answer 2

Length of boat typically correlates with the weight of the boat more than any other figure and it's pretty easy to determine length so that is why the Ark Ezi-Guides Self Aligning System part #AR64FR has a length range listed. This one is for 14…

view full answer...

Answer 3

The Ark Ezi-Guides Self-Aligning Boat Trailer Loading System can be used on bunk and roller trailers. The only requirement is a 1.96" - 2.57" cross beam for installation. You will also need to choose the correct system based on the boat…

view full answer...

Answer 4

That's a good question, so I reached out to Ark regarding the differences between the three systems, and you were on the money that the difference is the strength of the springs. Otherwise, the physical size and rollers on the guides are the…

view full answer...

Answer 5

While we haven't had a chance yet (May 2020) to install the Ark Eai-Guides, parts #AR64FR, #AR74FR, and #AR84FR, the beauty of boat trailers is that you can pretty much install rollers wherever you see fit. For now the rollers are only available…

view full answer...

Answer 6

Yes, The Ark Ezi-Guides Self-Aligning Boat Trailer Loading System #AR64FR can be used in salt water. The guides have a dacromet finish that will resist rust. Depending on how long your power boat or sailboat is we have a few options below: 14 foot to…

view full answer...

Answer 7

The Ark Ezi-Guides Self-Aligning Boat Trailer Loading System part #AR64FR has rollers which measure 14" long. I have attached a photo below with this measurement. Unfortunately this system will not work on a angled back section, it requires a…

view full answer...

Answer 8

I apologize for all of the confusion. I can tell you with absolute certainty that the Dutton-Lainson Roller Bunk Bracket, #DL21762, will pivot to allow the roller bunk to conform to the angle of the boat or watersport vehicle's hull. The hook…

view full answer...

Answer 9

The slots on the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System #AR64FR are tall enough to fit your trailer frame that is 2.5 inches tall. Now since your crossmember is V-shaped the U-bolt install would not work since this has to have a…

view full answer...

Answer 10

For your application I recommend installing roller bunks as well as some guide-ons to help make loading your boat MUCH easier with your conditions. The Caliber Marine Teflon Slides look like they would help to make loading/unloading the boat easier,…

view full answer...

Answer 11

The CE Smith Post-Style Guide-Ons for Boat Trailers #CE27640 can be used to replace your bunk-style guide-ons to protect your (very cool) 1963 Sea Skiff from potentially getting damaged by the bunk-style guide-ons. From what I can tell of the photo…

view full answer...

Answer 12

It depends on how tall your boat is. You want the posts to sit up above where the top sides of your boat are. You can see in the video I've included. So I recommend getting the 60" #CE27640 or the 75" #CE27636 guide ons.

view full answer...

Will Ark Ezi-Guides Self-Aligning Boat Trailer Loading System Non-Scuffing

Product Page this Question was Asked From

Continue Researching