Shock Absorbers in Convert-A-Ball Cushioned Ball Mounts

Question

Question:

How many shock absorbers are in AMSC4?

asked by: Cary G

0

Expert Reply:

The Convert-A-Ball Cushioned Ball Mount, # AMSC4, has two shock absorbers, one in front of the pin hole and one behind the pin hole. This is true for all Convert-A-Ball cushioned ball mounts. Check out the diagram I attached.

expert reply by: Robert G

0

click to enlarge

Answer 1

Weight distribution heads are adjustable to get the spring bars level or just below level with the trailer frame. Depending on the trailer frame, the head may need to be set at 90 degrees, it also may need to be tilted down as far as possible to keep…

view full answer...

Answer 2

Both the Convert-A-Ball shank, #AMAC1, and Curt shanks have hole spacing of 1-1/4 inches on center so you can use the AMAC1 on a Curt weight distribution system. I have included a link to a video review of the AMAC1 for you.

view full answer...

Answer 3

Ball mounts like the Curt #C45100 are available in various lengths. This one happens to be 13-inches long, longer than some. Longer ball mounts are needed, for example, in cases of a truck having a slide in camper in the bed, or when using a…

view full answer...

Answer 4

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 5

When you tilt the ball of a weight distribution system rearward on your hitch (toward the trailer) you are changing the physics of the system and therefore also the tension on the rear of the trunnion spring bars. Tilting the head rearward will take…

view full answer...

Answer 6

The Curt RockerBall Shock Absorbing 2" Hitch Ball part #C40047 will not work with a weight distribution system because the flange that gets wedged between the platform and base that stops the unit from rotating will not fit over the shank on a…

view full answer...

Answer 7

With the Curt Triflex part #C24VV and the Curt Adapter part #C51522 you will have all you need to successfully install your controller. I have linked a video for you showing the operation of the controller. Check it out to familiarize yourself with…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Shock Absorbers in Convert-A-Ball Cushioned Ball Mounts

Product Page this Question was Asked From

Continue Researching