Dimensions of the SumoSpring Helper Spring for a 2009 GMC Topkick

Question

Question:

the summo spring for a 2009 topkick, 2 wheel drive front axle. what is the length of this bump stop.

asked by: Rob J

0

Expert Reply:

The bump stop is 5" long on the SumoSprings Solo Custom Helper Springs - Front Axle item # SSF-281-47. The bracket is 7/8". This is a confirmed fit for a 2009 GMC Topkick. I have attached a diagram I made below.

expert reply by: Jerred H

0

SumoSprings Solo Custom Helper Springs Dimensions
(click to enlarge)

Answer 1

I will start off by saying that the Replacement Bushing #RM-205381-00 is the direct replacement for the Roadmaster Polyurethane Bushing Kit for 1-3/8" Diameter, Factory Rear Anti-Sway #RM-4139-300. To further that, the Replacement Polyurethane…

view full answer...

Answer 2

We have Superspring kits that are a confirmed fit for your 2005 Chevy Kodiak. For the rear axle you'd need the part #SSA25 and then for the front you'd want the #SSF-281-47 which is the leaf spring style. This setup gives you a SumoSpring in…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The air suspension system on your 2022 Ram 2500 limits your options for suspension enhancement. None of the air bags made for your truck will be compatible. Instead, I recommend adding the SumoSprings Rebel Custom Helper Springs #SS64VR. The…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 7

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 8

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 11

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Dimensions of the SumoSpring Helper Spring for a 2009 GMC Topkick

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching