Can Dutton Lainson StrongArm Winch be Powered from Battery in Back of Truck

Question

Question:

Can I run off opt battery in back of my truck can I hook just to pos and neg to fun the winch

asked by: Steve

0

Expert Reply:

Yes, if you have a battery in the back of your truck you can connect the wires of the Dutton-Lainson TW4000 StrongArm Electric Winch # DL25200 to power it.

expert reply by: Jameson C

0

Answer 1

There could be two possible reasons as to why the clutch is not engaging when you are pulling in your boat with the Dutton-Lainson TW4000 StrongArm Electric Winch part #DL25200. The first reason is the simplest to fix and it entails tightening the…

view full answer...

Answer 2

There is indeed a remote available for you to add to your Dutton-Lainson TW4000 StrongArm Electric Winch #DL25200. What you need is the following part: - Dutton-Lainson Remote Hand-Held Switch for DC StrongArm SA Series Electric Winches #DL24054

view full answer...

Answer 3

Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but with…

view full answer...

Answer 4

The wiring kit needed to power the Dutton Lainson TW4000 part #DL25200 that you referenced is the part #DL24152. The power outlet on your truck would not have the amperage rating to power this winch. The wiring kit mentioned has thick gauge wires…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Can Dutton Lainson StrongArm Winch be Powered from Battery in Back of Truck

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching