Availability of Longer Ball Mount to Fit 2 inch Trailer Hitch

Question

Question:

I am looking for a long shank class iv 2x2 ball mount. Do you sell one?

asked by: David T

0

Expert Reply:

The Hidden Hitch ball mount part # 80232 is a longer ball mount that fits 2 inch hitches. It is 15-3/4 inches from the pin hole to the ball hole center. This is a Class III ball mount but there aren't any in Class IV.

expert reply by: Jameson C

0

Answer 1

For your 2013 Jeep Wrangler JK Unlimited I recommend the Hidden Hitch Ball Mount #80232. This ball mount has a length of 15-3/4"(400mm) from center of hitch pin hole to center of ball hole. That will give you an additional 3-15/16"(100mm)…

view full answer...

Answer 2

We have longer weight distribution shanks like the Curt part #C17122 which measures 14 inches from the center of the hitch pin hole to the vertical holes of the shank. You're pretty lucky your trailer manufacturer said it was okay to use a WD…

view full answer...

Answer 3

I would be happy to help! The longest ball mount we offer is theBrophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs #BM20 which measures 13-1/4" from the center of the hitch pin hole to the center…

view full answer...

Answer 4

It sounds like you're needing a longer ball mount like the Hidden Hitch Ball Mount #80232. This measures 15-3/4" from the center of the hitch pin hole to the center of the hole where the hitch ball is installed which should be pretty close…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 11

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Availability of Longer Ball Mount to Fit 2 inch Trailer Hitch

Product Page this Question was Asked From

Continue Researching