Replacement Plastic Inside Housing Pieces for Yakima SpaceCadet Roof Box

Question

Question:

I have a Yakima Space Cadet and the plastic housing on the inside of the carrier that protects the sliding bars and helps them lock into place has broken. Do you know how I can replace the plastic housing?

asked by: Zachary

0

Expert Reply:

I believe the kit you're looking for is Replacement Seal Strips for Yakima SkyBox 16 Rooftop Cargo Box # 8870085 which comes with 4 of these strips that fit the older SpaceCadet boxes.

expert reply by: Jon G

0

Answer 1

The correct seals for a Yakima SkyBox 16 Roof Cargo Box are the Replacement Seal Strips for Yakima SkyBox Series Rooftop Cargo Box part #8870086.

view full answer...

Answer 2

Thank you for all of the info and pictures! I forwarded them on to my contact at Yakima and it looks like you have the old SkyBox Pro 16 Silver 8007179. Even though this box has been discontinued we do have quite a few replacement parts for it: Cam…

view full answer...

Answer 3

Yes, your Yakima Space Cadet roof top cargo box is compatible with Yakima's Same Key System (SKS) Lock Cores #Y07208. I was able to confirm this information with Yakima. They had not heard of an issue with the control keys but be sure to try the…

view full answer...

Answer 4

If your 2020 Jeep Grand Cherokee has adjustable rails you can move them forward on the vehicle to allow for more spacing. There is also adjustment capability made into most of the Thule Roof Boxes like the Thule Force XT L Rooftop Cargo Box part…

view full answer...

Answer 5

The Thule Sidekick #TH78GC has a minimum bar spread of 23 5/8" and a maximum bar spread of 28". The mounting width is 14 3/8" .The Front Clearance is 36" and the Front Clearance Max Bar Spread 26". If you're not fully…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Replacement Plastic Inside Housing Pieces for Yakima SpaceCadet Roof Box

Product Page this Question was Asked From

Continue Researching