Replacement 1/2" Diameter Pin for Trailer Jack

Question

Question:

I need a replacement. swivel pull pin for a Jeremywell JMW trailer jack. The pin is 1/2 inch diameter. The straight portion of the pin fits thru the holes needs to be at least 2 1/4 inches long - preferably 2 1/2.

asked by: Gary K

1

Helpful Expert Reply:

We do not carry the jack you are needing a replacement part for. The closest pin we have to what you are describing is the Replacement Plunger Pin Assembly for etrailer and Ram Jacks # PLGPIN-12 which is 1/2" diameter, a total of 5" long and the straight portion is 2-1/2".

expert reply by: Scott S

1

etrailer Jack Pin Measurements
(click to enlarge)

Answer 1

The Replacement Plunger Pin Assembly for etrailer and Ram Jacks #PLGPIN-12 has a 1/2" diameter, measures 5" long, and the straight part measures 2-1/2" (see attached photo). We used to carry the Shelby jacks back in the day when they…

view full answer...

Answer 2

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 3

I pulled both products from the warehouse to measure and compare for you. The Dutton-Lainson pin #DL22454 (unlike the page photo) has the cotter pin hole in line with the handle and is 1-7/16 inches from the end to the cotter pin hole center. The…

view full answer...

Answer 4

The plunger pins are usually specific to the brand of jack and usually are not interchangeable. Unfortunately, without knowing the manufacturer and model number of your existing jack, I cannot say with certainty that the pin will work for you. I have…

view full answer...

Answer 5

We offer four different 1/2-inch diameter plunger pins that are shown on the linked page. Two of the four are bent pins, parts #F0933307S00 and #PLGPIN-12 that you referenced. I went to our warehouse and measured both of these. While they are not…

view full answer...

Answer 6

To replace your plunger pin on your Shelby Jack I recommend Replacement Swivel Pin Kit for Trailer Jacks Item #DL22454. As long as your pin is 1/2" diameter this kit can replace your current pin.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Replacement 1/2" Diameter Pin for Trailer Jack

Product Page this Question was Asked From

Continue Researching