Longer Ball Mount Solution to Help Tailgate to Trailer Jack Clearance

Question

Question:

I have a 22 foot tow behind camper. Toung weight 560 lbs. Trailer weight empty 5700 lbs I need an extended hitch because my tailgate hits the electric toung lift. Any ideas?

asked by: Ron K

0

Expert Reply:

Normally for this situation the best solution is a longer ball mount like the Hidden Hitch part # 80232 which is 15-3/4 inches long and will give you additional clearance between the truck and the trailer jack for your tailgate.

expert reply by: Jameson C

0

Answer 1

When It comes to using a weight distribution while towing a trailer using The Hitch Box Extension and Reducer for Titan 2-1/2" Trailer Hitches, 24 inch - 34 inch Long #RP45292 I would recommend The Fastway e2 Weight Distribution w/ 2-Point…

view full answer...

Answer 2

Technically any additional length is going to increase leverage on the trailer hitch. But there isn't an exact standard length ball mount so going super technical on how much the force multiplied when the ball mount is beyond a certain length is…

view full answer...

Answer 3

For your 2013 Jeep Wrangler JK Unlimited I recommend the Hidden Hitch Ball Mount #80232. This ball mount has a length of 15-3/4"(400mm) from center of hitch pin hole to center of ball hole. That will give you an additional 3-15/16"(100mm)…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

I would love to help you with this Adam, but I am going to need a bit of information on your exact setup to determine what all you will need. Can you tell me how heavy your car trailer is when loaded and how much extension you will need? Also I will…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Longer Ball Mount Solution to Help Tailgate to Trailer Jack Clearance

Product Page this Question was Asked From

Continue Researching