Roof Vent Cover That Will Hold In Stronger Winds For A 2021 Riverstone 3950FWK

Question

Question:

Would this vent cover be a good solution to strong wind coming from the rear of the rv? I am parked north/south and have strong winds. When opening the bathroom roof vent it sounds like it will be ripped off the roof any time wind is above 10- mph. 2021 Riverstone 3950FWK

asked by: Mark D

1

Helpful Expert Reply:

The MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip # MA86JR will work great with your 2021 Riverstone 3950FWK.

This vent cover has locking latches that latch over top your roof vent, and secures via the use of EZ clips, but if you're installing this over a high-powered, high-speed ventilation fan, use the included self-tapping screws to mount the cover instead.

This vent cover should work just fine in the stronger wind situations you've been experiencing.

expert reply by: Bryce D

1

Answer 1

No the MAXX AIR II Vent Cover #MA86JR that you referenced does not come with a bug screen built into it. Just the screen is not available as it does not separate.

view full answer...

Answer 2

We do have the following screens and sleeves for your Ventline V2094 roof vent on your 2013 Jayco Featherlite Hybrid X23B. I have included some parts as an assembly and some other parts based on on exactly what all you want to replace with your vent.…

view full answer...

Answer 3

The MaxxAir FanMate vent cover Item #MA00-955001 is going to be just a little taller but the louvred end tapers in and it does not come with the screen which is Item #MA00-955202. 25" long x 18-1/8" wide x 10-1/4" tall. The MaxxAir II…

view full answer...

Answer 4

The Ventline Ventadome EZ Lift part #V3092-601-00 would be a great option James. This is a basic RV roof vent with a manual raise lid like you are looking for.

view full answer...

Answer 5

If you're talking about the actual lid for the vent then you can use the MaxxAir UniMaxx Universal Replacement Lid #MA00-335002 as a replacement no matter the brand vent you have. This lid has a universal fit hinge that will mount to your current…

view full answer...

Answer 6

The Replacement Screen Frame with Screen for Ventline Ventadome Powered Lift Roof Vents #BVC0573-32 you mentioned is meant to work with the Ventline Model V2119, and not your Model V2094, unfortunately. Instead, you'll want to take a look at the…

view full answer...

Answer 7

The MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip #MA86JR that you referenced is not translucent so it does not allow any light to pass through it. There isn't a smoke version of this available.

view full answer...

Answer 8

Yes, your MaxxAir fan is going to be 14"x14", the real determining factor for your fan cover is the model and hinge style of the cover. For your standard MaxxAir fans you can replace the cover with the MaxxAir UniMaxx Universal Replacement…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...