What Replacement End Caps do I Need for My Rhino-Rack Heavy Duty Crossbars?

Question

Question:

'Im looking for the end caps for rhino rack hd cross bars. I need all 4. Do you guys stock them or can you acquire them?

asked by: Eric

0

Expert Reply:

We definitely have them! The replacements you need for your Rhino-Rack Heavy Duty Crossbars like the # RB1375B-2 is the Replacement Endcap for Rhino-Rack Heavy-Duty Crossbars - Qty 1 # RRM002. It is important to note that each of these comes with a quantity of 1, so you will need to order 4 total.

expert reply by: Bob C

0

Answer 1

For a heavy duty roof rack system for your 2022 Jeep Wrangler Sahara Unlimited I recommend the following parts: Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 59" Long - Qty 3 #RB1500B-3 RCL Legs for Rhino-Rack Crossbars and Pioneer…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To utilize the Titan Chain Sliding Lashing Winch for Flatbed Truck or Trailer #TCLR900 you need the following: - Brophy Winch Bar for 2" Lashing Winch #W2BZ - etrailer Sliding Winch Track #e48ZR

view full answer...

Answer 11

The only troubleshooting you can really do with the K-Source Custom Extendable Towing Mirrors #KS62093-94G would be to check that the wire harness is fully connected and that you didn't blow a fuse in the truck that could've killed the power…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

What Replacement End Caps do I Need for My Rhino-Rack Heavy Duty Crossbars?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching