What Side Cab Steps do You Recommend for My 2013 Mercedes Sprinter Cab/Chassis?

Question

Question:

Interested in running boards for a 2013 3500 Mercedes Sprinter chassis cab not van could be max of 35 ~890mm long. We would also consider just a step rather than a running board. There is no rear box on the back - just the frame/chassis. Thank you,

asked by: Valerie S

1

Helpful Expert Reply:

Thanks so much for all of the information! As far as running boards for your 2013 Mercedes Sprinter 3500 cab/chassis, the only ones we carry are designed to fit models that have sliding doors. This is the Aries RidgeStep Running Boards # AA86ZB. With this set, you will not have the same length of boards on both sides of the cab because the passenger's side is shorter than the driver's side. Also, we cannot confirm whether this set fits on a cab/chassis model.

For a great alternative that 100% works with your cab/chassis model, I recommend the Carr Custom-Fit Side Steps - Super Hoop - Black Powder Coated Aluminum - 17" Step # CARR125771 (black) or # CARR125772 (silver). These steps can be mounted anywhere along the space below your doors. They do involve drilling for installation. I went ahead and attached a video that walks you through the process.

expert reply by: Bob C

1

Answer 1

You're correct, the SumoSprings Rebel such as part #SSR-327-47-2 is compatible with 4WD vehicles only. For a 2WD vehicle, I'd recommend the SumoSprings Solo, part #SSR-330-47 which would add 900 lbs of support for your payload. For a higher…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 8

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 9

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

What Side Cab Steps do You Recommend for My 2013 Mercedes Sprinter Cab/Chassis?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching