What Complete Mounting Hardware Set Works with the 10-Pack of Hydraulic Trailer Brakes # ETBRK435A?

Question

Question:

Do you sell the mounting hardware that comes with all of the ETBRK435A?

asked by: Damien

0

Expert Reply:

Yes! For a complete set of mounting hardware for the 10-pack of Hydraulic Trailer Brakes - Uni-Servo - Free Backing - 10" - Left/Right Hand - 3.5K # ETBRK435A, that is the Mounting Hardware for 10" Brake Assemblies - 10 Pairs # BRKH10B10.

expert reply by: Bob C

0

Answer 1

Absolutely. Your 1998 Fleetwood Mallard 24J will use 10 inch brake assemblies which are designed to work with 10 inch hubs so the measurements aren't literal. I recommend using the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and…

view full answer...

Answer 2

I went ahead and called my contact at Redline Trailer Repair Parts, and they confirmed that nuts in the Mounting Hardware for 10" Brake Assemblies #BRKH10B have a diameter of 7/16mm and have 20 threads per inch. Unfortunately, there are no bolts…

view full answer...

Answer 3

In order to determine what size brakes you need you will need to measure what you currently have on your trailer. Check out the picture I attached that shows you exactly where to measure. If you are instead looking for a way to add brakes to your…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

What Complete Mounting Hardware Set Works with the 10-Pack of Hydraulic Trailer Brakes # ETBRK435A?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching