Does Ultimate Trailer Jack Fit Standard A-Frame Mounting Bracket

Question

Question:

Are most or all the same size and bolt pattern?

asked by: Richard J

1

Helpful Expert Reply:

Yes, nearly all trailer a-frame bolt patterns for jacks are the exact same so you don't have to measure or verify anything to know that the Ultimate trailer jack # 322-RDJ-2K will fit your trailer.

expert reply by: Jameson C

1

Answer 1

To allow the post of the Ultimate Trailer Jack #322-RDJ-2K to slide up and down, loosen the 3 mounting bolts used to attach to your A-Frame. Check to see if this allows the jack post to move. If it does, you'll want to tighten the bolts by hand…

view full answer...

Answer 2

Yes, the Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs #322-RDJ-2K you were looking at can be removed from the mounting bracket by removing the keeper pointed out in the included diagram, and then removing the foot. After…

view full answer...

Answer 3

Unfortunately I did not get the pictures, but I do have an idea of what you are looking for based on your description. I recommend the Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs #322-RDJ-2K. I've attached a video of…

view full answer...

Answer 4

The best trailer jack for tailgate clearance like you are wanting is the Ultimate Trailer Jack #322-RDJ-2K as it can lower nearly totally flat if needed. Check out the review video I attached for more info.

view full answer...

Answer 5

We can help you with a replacement 7-way trailer harness for your 16-foot trailer. All such items are shown on the linked page. These include plugs-only, such as #PK12706, which uses your trailer's existing wiring; pigtail plugs like #54006-059…

view full answer...

Answer 6

I may have a solution for you. Your Casita travel trailer has an a-frame. My jack recommendation works a-frame trailers. If your a-frame has pre-threaded holes for your jack, this option may not work for you. While we do not carry Jack-E-Up adapters,…

view full answer...

Answer 7

According to the manufacturer, the bolt and the plastic retainer of the #322-RDJ-2K Ultimate trailer jack are removed, then replaced after thread lock is applied to the bolt threads. Be sure that the V that protrudes from the retainer rides in the V…

view full answer...

Answer 8

Yes, you can mount the Ultimate Trailer Jack part #322-RDJ-2K so that the release pin faces outward instead of towards the trailer. All you need to do is rotate the jack until the mounting holes line up and the pin is pointed away from the trailer.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Does Ultimate Trailer Jack Fit Standard A-Frame Mounting Bracket

Product Page this Question was Asked From

Continue Researching