How Do You remove a Rear Bump Stop On A 2021 Chevy Silverado

Question

Question:

What tool do I need to remove 2021 Silverado bump stop rear

asked by: Paul P

0

Expert Reply:

When we removed the rear bump stops, we found that by using a 10 mm socket and ratchet to take the bolt down. You may have to switch to a smaller ratchet but still using the 10 mm socket to get it completely off, and after you finished taking them off you add install the Timbren Rear Suspension Enhancement System.

I put an installation video below.

expert reply by: Noah E

0

Answer 1

The most popular suspension enhancement for a 2021 Chevrolet Silverado 1500 is the Timbren Rear Suspension Enhancement System part #TGMRCK15S. They work very well, are easy to install, and they require no maintenance which is what makes them a…

view full answer...

Answer 2

The main difference between the Timbren Rear Suspension Enhancement System part #TGMRCK15S and SumoSprings Solo Custom Helper Spring part #SS45FR for a 2019 Chevrolet Silverado 1500 is hardness. The Timbrens are much denser than the SumoSprings so…

view full answer...

Answer 3

Yes. The Timbren #TGMRCK15S are a confirmed fit on the 2019 Chevy Silverado 1500 LT. These Timbren springs provide an easy to install solution to help keep your truck level during towing and fight body roll. I've linked a short review and…

view full answer...

Answer 4

The best way to determine how many spacers you need for the Timbren Suspension Kit item #TGMRCK15S, for your 2020 Chevy Silverado 1500, is to measure the distance from the underside of your frame where your bump stop sits to the axle directly below…

view full answer...

Answer 5

The bump stop of your 2020 Chevy Silverado 2500 actually is not held in with a bolt and to remove it you would just need to pry it out.

view full answer...

Answer 6

The SumoSprings Solo Custom Helper Springs, part #SS45FR, for the 2020 Chevrolet Silverado 1500 are meant to have that 1-1/2" gap when there is no load. This is to ensure that the ride isn't stiff while unloaded. Adding spacers would negate…

view full answer...

Answer 7

The factory lift of your 2019 Chevy Silverado 1500 Trail Boss would not require you to use additional spacers to fit a Timbren kit like the part #TGMRCK15S. The best suspension enhancement for your truck is the RoadActive Suspension kit part #RAS4611…

view full answer...

Answer 8

Thanks for the photo and the Timbren Rear Suspension Enhancement System #TGMRCK15S you mentioned is a good option for helping keep your 2020 Chevy Silverado 1500 level, but the best option is something a little different, the RoadActive Suspension…

view full answer...

Answer 9

Since your trailer is about 5000lbs meaning your tongue weight is between 500-750lbs, and you are adding an additional 400lbs to the bed of your truck you are adding around 1150lbs to the rear of your 2021 Chevrolet Silverado RST Z71 4x4. With that…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

How Do You remove a Rear Bump Stop On A 2021 Chevy Silverado

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching