Replacement Endcaps for the Thule Crossbar Set-Hybrid Part Number SOA567X060 from Subaru

Question

Question:

Do you carry this part? I have a 2020 Subaru Crosstrek HYBRID. One of the endcaps came off the Thule roof rack which is made specifically for this car I think and is missing. I would like to replace the cap if possible. The rack isThule® Crossbar Set - Hybrid Part Number: SOA567X060. I am missing the driver side back endcap. Thank you!

asked by: Shawn

0

Expert Reply:

I contacted Thule in regards to your question. The Thule Crossbar Set - Hybrid Part Number: SOA567X060 from Subaru uses the Thule AeroBlade Load Bars ARB47. The correct drivers side endcaps for those load bars is the Replacement Endcap for Thule Aeroblade Load Bars # 752-2867001.

We also have the passenger side available which is Replacement Endcap for Thule Aeroblade Load Bars # 752-2867002.

expert reply by: Scott S

0

Answer 1

In regards to the Replacement Endcap for Thule Aeroblade Load Bars, part #752-2867002 for passenger side or part #752-2867001 for driver side, there is a tab on the bottom of the bar you must push-in and then you can pull the old end cap out. In…

view full answer...

Answer 2

We do offer one of those parts, which are the replacement end caps for your crossbars (which you mentioned were Streamline though I believe you were referring to the JetStream). What you need for those is the Replacement Endcaps for Yakima…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The Curt #C13410 and Draw-tite #76227 are very similar in design and both have the same weight ratings of 600lbs tongue weight and 4,000lbs of trailer weight. I do like that Draw-Tite does add the additional plate of steel in between the hangers…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 7

The foam panel is in the bumper to help support the bumper panel as well as provide a cushion for the cover if there is a minor collision. Without the cushion the cover will tend to break or crack easier as it does not have the support needed. I have…

view full answer...

Answer 8

We do have what you need to add a 7-way trailer connector to your 2018 Subaru Outback Wagon but there isn't a specific custom harness that fits. If right now the Outback has no trailer wiring at all the easiest way to add a 7-way is to start with…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 11

The information I have says the #306-X7162 has a ground clearance measurement of 10-1/2". The Curt #C13410 has approximately 12" to 12-1/2" of clearance when measured to the bottom of the receiver. I'm not 100% sure how accurate…

view full answer...

Answer 12

I recommend installing the Curt Trailer Hitch Receiver #C13410 on your 2018 Subaru Outback. This receiver will fit with the Hollywood Racks Sport Rider SE2 Bike Rack #HR1450Z and provide you enough clearance both when folded and unfolded. This bike…

view full answer...