Dimensions of the Replacement Cover for TruXedo Lo Pro Soft Roll-up Tonneau Cover

Question

Question:

Hi, what is the exact size of this replacement cover. I’m trying to match it up to the one that is built into my trac rac system Thank you

asked by: Stephen F

1

Helpful Expert Reply:

The Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover # TX5467-CVR measures 97" long by 62-3/4" wide. It is the correct replacement tarp for the TruXedo model number TX546701 cover.

expert reply by: Scott S

1

Replacement Cover for Truxedo Lo Pro Soft Roll-up tonnjeau Cover Dimensions
(click to enlarge)

Answer 1

If your 2010 Dodge Ram 2500 was a short bed truck the correct Truxedo Lo Pro replacement tarp would be the #TX546901-CVR or if it was a long bed truck you'd need the #TX5489-CVR.

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 8

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 9

The Air Lift Air Helper Spring Cradles #AL59DQ are not going to be compatible with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL57589 on your 2021 Ram 2500. This is due to the 7500 springs being larger in diameter than the 5000…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Hey Jeff, The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails #311-JED7833 is designed for a 6-1/2' bed while the #311-KRD7936 is designed for an 8' bed. Since you have a 6-1/2' bed the #311-JED7833 would be the…

view full answer...