Compatibility Of Dexter 6,000LB Hub And Drum Assemblies On etrailer AxleTek 7,000LB Axles

Question

Question:

Will a the dexter hub and drum assembly fit on an axle tek axle? I want to replace my tandem 6k dexter axles with 2-7k axle tek axles. Will I be able to reuse my existing bearings and hubs?

asked by: Ken M

0

Expert Reply:

To verify if your hubs on your 6,000lb Dexter axles are going to fit the etrailer AxleTek 7,000LB Axle # e35GR you will need to verify what bearings and grease seals are used on your hubs. The new axles will use a #42 Spindle # TRU57FR, and this is the most common spindle used on the Dexter 6,000lb axles. The etrailer AxleTek uses Inner Bearing # 25580(ID 1.750"), Outer Bearing # 14125A(ID 1.250") and Grease Seal # GS-2250DL(ID 2.250", OD 3.376").

The Dexter Trailer Hub and Drum Assembly # 42866UC3-EZ and Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-464-465 can be used if your current hubs and brakes are worn.

expert reply by: Bud M

0

Identifying Bearings, Races and Grease Seal Part Numbers and Dimensions
(click to enlarge)

Answer 1

From a spec standpoint the Dexter 7k trailer axle part #8327872 is exact same as the etrailer part #e35GR. Most would consider the Dexter axles to be the very top of the line in terms of quality but our etrailer brand is also a really solid option…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Compatibility Of Dexter 6,000LB Hub And Drum Assemblies On etrailer AxleTek 7,000LB Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching