Brake Controller Power Wire Location on 2011 Chevy Silverado 3500
Question:
My truck come with a factory brake controller. I have made the connections in the cab but dont have power to the controller. I found one of the two wires under the hood that has to be connected. I can not locate the one that should be next to the brake booster.
asked by: Ryan W
Expert Reply:
In regards to a 2011 Chevrolet Silverado 3500, the power ring terminal for a trailer brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 is located directly to the right of the power distribution box. It is taped to a wire harness between the driver-side front fender and the power distribution box. Cut the tape to release it from the harness. Then run the wire to the front of the power distribution box and hook the ring on the left post (M6 stud). You may also need to activate the brake controller power post by inserting an automotive style 30-amp fuse into the correct slot in the power distribution box. I have attached a photo below of the connections.
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM
- Shop: Pollak 7-Pole, RV-Style Trailer Connector Socket w/ Wiring Harness and Mounting Bracket
- Shop: Trailer Wiring
- Shop: Gooseneck Hitch
- Search Results: trailer hitch
- Shop: 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Plug - GM, Ford, Ram, Toyota - 9' Long
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: B&W Rubber Cover for Stowed Turnoverball
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Search Results: tekonsha trailer brake controller
- Q&A: Installation of Brake Controller on 2011 Chevy Silverado Where No Power Is Present on Wires
- Q&A: No Power to Brake Controller After Install
- Q&A: Where are the Power Wires Located for the Electric Brake Controller Box and 7-Way Trailer Connector
- Q&A: Installing 12-Volt Accessory Trailer Power Feed Fuse in 2010 GMC Sierra
- Q&A: Brake Controller On My 2011 Chevrolet Silverado W/ Tow Package Gets No Power After Installation
- Q&A: Troubleshooting Flashing Blue Screen on Tekonsha Prodigy P3 Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Aftermarket Brake Control Wiring for 07-13 GM Full-Size Truck with Factory-Integrated Brake Control
- Search Results: tekonsha p3
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Search Results: brake controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Search Results: trailer brake controller
- Video: Choosing the Right Brake Controller