Replacement Hangers, Equalizers, Shackle Straps and Hardware For a Trailer with 5-5/8" Equalizer
Question:
Trying to rebuild my trailer suspension and having trouble finding the right kits the Equalizer on the trailer is part number 13–104 and that is it.. it measures out 5 5/8 And the shackles measure around 2 3/4s center hole to center hole . Now I have looked at some of y’all’s kits. Example one of the kits part number 13-104-2 Equalizer then I click on the kit Amd that equalizer measure too big . Also I need to replace the hangers to the front and rear hangers measurements 2 1/2 from the top down to the center of the hole. Then the center hanger measurements are from the top down to the center of the bolt hole is 3 1/4 . If you guys can point me in the right direction would be awesome thanks
asked by: Josh
Expert Reply:
You will need the following parts as we do not have everything you need in one kit.
Front/Rear Hanger # 115918 Qty 4
Center Hanger # 28-5 Qty 2
Curved Equalizer # TREQ104 Qty 2
Shackle Strap # CE14103G Qty 8
Zinc Shackle Bolt with Locknut # TRFA73Z916DLNZ Qty 14
You can swap the hardware for the Wet Equalizer Bolt # 126B2 if you wish to have a greased set of bolts that allow the suspension to move more freely. You will need to replace the nylon bushings in your springs and equalizer for Bronze Bushings # K71-291-00.
Products Referenced in This Question
Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Trailer Leaf Spring Suspension
- Suspension Bolts
- Camper
- Car Hauler
- Utility Trailer
- 9/16 Inch Diameter
- 2-5/16 Inch Long
- Redline
more information >
Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Trailer Leaf Spring Suspension
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 3-1/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- etrailer
more information >
CE Smith Shackle Strap - Galvanized Steel - 2-3/4" Hole-to-Hole Length
- Trailer Leaf Spring Suspension
- Shackle Links
- Boat Trailer
- Snowmobile Trailer
- 2-3/4 Inch Long
- CE Smith
more information >
Dexter Bronze Bushings - Qty 4
- Trailer Leaf Spring Suspension
- Bushings
- Boat Trailer
- Snowmobile Trailer
- 9/16 Inch ID x 11/16 Inch OD
- 1-3/4 Inch Long
- Dexter
more information >
Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 5-3/4" Long - 9/16" Center Hole
- Trailer Leaf Spring Suspension
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 5-3/4 Inch Long
- Tandem Axle
- Triple Axle
- TruRyde
more information >
Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Trailer Leaf Spring Suspension
- Suspension Bolts
- Boat Trailer
- Snowmobile Trailer
- 9/16 Inch Diameter
- 3 Inch Long
- TruRyde
more information >
Product Page this Question was Asked From
Front/Center/Rear Hanger for Double-Eye Springs - 2-3/8" Tall - 9/16" Bolt Hole
- Trailer Leaf Spring Suspension
- Hangers
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 2-1/2 Inch Tall
- Tandem Axle
- Triple Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Where to Position the Trailer Axle?
- Q&A: What is Needed to Add Second Axle
- Article: Double-Eye Trailer Suspension System Review
- Article: Slipper Spring Trailer Suspension System Review
- Q&A: What is Recommended Clearance between Trailer Axle and Frame
- Q&A: How to Determine Hanger Spacing for Tandem Axle Trailer Suspension with 26 Inch Springs
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Q&A: Installing Leaf Springs on Single Axle Trailer
- Q&A: Would the Replacement Square End Cap 853-5826 Fit Gorilla Lift GL1
- Q&A: Spring Compression for the etrailer 4-Leaf Slipper Spring While Under a 1,000 lb Load
- Article: Most Popular Wheel Bearings
- Article: How to Raise Your Travel Trailer Height
- Q&A: How to Select Hubs That Are Compatible with Trailer Spindle
- Article: How to Replace Trailer Leaf Springs in 5 Steps