Correct Replacement Bearings and Seals for Lippert 4,400 Lb Axle

Question

Question:

Hi, I have a 2020 Grand Design Imagine 2600rb trailer. I need the part # for Wheel Bearing In out side and the seal. For 4,400 Axel capacity

asked by: Johnny

0

Expert Reply:

The Lippert 4,400 Lb Axle uses part # L68149 for the inner bearing and part # 58846 for the grease seal. The outer bearing can be either part # L44649 or part # LM67048. The L44649 I believe is for 5-lug and the LM67048 I believe is for 6-lug but I recommend measuring or reading the part number before purchase.

expert reply by: Conner L

0

Answer 1

I reached out to my contact at Lippert who confirmed the bearings and seal included with the Hub Bearing Kit #BK2-100 is what you need for each up on your trailer axle. Attached is an installation video for you to check out.

view full answer...

Answer 2

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

view full answer...

Answer 3

I checked with Lippert and could not find any information on NV304664. Do you know the capacity of the axle? If it is a 7,000 pound axle then the likely inner bearing is #25580 and the outer bearing is #14125A. If a 2-1/4 inch seal diameter is needed…

view full answer...

Answer 4

We do have the bearings you need for your Lippert 4,400 lb trailer axle: - Inner bearing #L68149 - Outer bearing #L44649 You can also get the bearings, races and seal with one kit, the Bearing Kit #BK2-100. If you are looking for grease as well, I…

view full answer...

Answer 5

In regards to a shackle bolt like the Wet Equalizer Bolt with Locknut part #126B2, there is no recommended torque setting. They're tightened until the knurled portion of the bolt pulls completely into the shackle strap and the bolt head is ran…

view full answer...

Answer 6

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using has a…

view full answer...

Answer 7

If you're just wanting to replace the converter cross section of your PD4560 power center to be compatible with lithium batteries then yes, you'll want the Replacement Lithium Converter for Progressive Dynamics 4500 Series RV Power Control…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 10

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 11

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 12

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Correct Replacement Bearings and Seals for Lippert 4,400 Lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching