Correct MORryde Cushioned 5th Wheel Pin Box for a Grand Design Reflection 31M

Question

Question:

Which moryde pin box should I purchase to reduce my chucking for 2020 Grand Design Reflection 31MB

asked by: Mark D

1

Helpful Expert Reply:

The correct MORryde Cushioned 5th Wheel Pin Box for a Grand Design Reflection 31M is part # MR74VR.

expert reply by: Conner L

1

Answer 1

The correct MORryde Cushioned 5th Wheel Pin Box for a Grand Design Reflections 337RLS is part #MR84VR. This pin box will do a wonderful job of helping smooth the ride due to the internal cushioning which reduces road shock.

view full answer...

Answer 2

While the MORryde #MR74VR is rated up to 18,000 pounds, it is optimized to give the best ride for trailers weighing 11,500 to 14,000 pounds. This will be a very good choice for your Reflection as long as it has the 1621 or 1621HD bolt pattern - which…

view full answer...

Answer 3

In order to use the B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter part #BWRVK3400 along with the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1116 on your 2017 Ford F-250 FX4 you…

view full answer...

Answer 4

Capture plates are designed to be used with auto slide hitches like the Demco Highjacker #DM8550034 or the PullRite Auto Slide hitches. As the B&W Companion #BWRVK3305 is a fixed fifth wheel hitch, you do not need a capture plate. If you are…

view full answer...

Answer 5

If they welded the capture plate of your Pullrite hitch to the pin box you would either have to remove the capture plate or replace the pin box. Typically these plates aren't welded on. If you can find me the pin box model name and number I can…

view full answer...

Answer 6

The rear jacks in the Lippert Ground Control system #LC358590 stick out from the frame by approximately 4 inches. They are 24-1/2 inches tall when fully retracted. And when fully retracted there should be 7 to 9 inches of ground clearance. The…

view full answer...

Answer 7

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 8

We have a heat shield #RT76FR for applications like your 2017 Chevy Silverado 2500 where the exhaust points right at the flap of the part #ERT00108. This would be your ideal solution and would work well.

view full answer...

Answer 9

The angle of the arms that hold the flaps of the Rock Tamers Heavy-Duty, Adjustable Mud Flap System #ERT00108 are adjustable so that you can add distance between the tail pipe and them as needed. If you install the heat shield part #RT76FR that you…

view full answer...

Answer 10

When installing Rock Tamer Mud Flaps, there is not an exact distance that it needs to be form the exhaust. If the exhaust on your truck is routed straight back then you will want to install Exhaust Outlets #ERT200 so that the exhaust is routed…

view full answer...

Answer 11

The best replacement pin box for the Lippert 1621 on your Grand Design Reflection 303RLS is the Curt Flex Air. This pin boxes has an air spring and shock absorber which will reduce the back and forth chucking (stopping and taking off) and lower the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...