Mounts for Cargo Carrier for RV Bumper

Question

Question:

Do you sell just the brackets and the arms ? Already have a platform.

asked by: Art

0

Expert Reply:

The 24x84 etrailer Cargo Carrier for RV Bumper, # e96ZR is sold as an assembly. We do not have an option for what you are looking for.

expert reply by: Michael R

0

Answer 1

The distance between each of the mounting brackets of the 24x84 etrailer Cargo Carrier for RV Bumper #e96ZR is 27-9/16 inches. The picture I attached came from the install instructions which are also linked on this page as well.

view full answer...

Answer 2

The 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR weighs 82 lbs. Therefore, the bumper must be rated for the weight of the carrier and all cargo, up to 500 lbs. In order to verify the weight capacity of the bumper, you'll need to…

view full answer...

Answer 3

The Yakima Rack and Roll Trailer - 78", part #Y08107, has an adjustable cross bar spread. It can be adjusted from 4" to 48". so the wheel base of your trike will not be a limiting factor. You can use any bike rack that can…

view full answer...

Answer 4

The Lippert Underchassis Storage Bin, part #LC175180 measures 10-3/16 inches from the top of the mounting strap to the bottom of the storage bin. The mounting straps measure approximately 1/10 of an inch. If you decide you want to shim the frame…

view full answer...

Answer 5

The Lippert Underchassis Double Bin Storage Unit #LC175180 referenced in your question will bolt directly onto the underside of your Lippert Chassis. The only thing that could possibly cause interference is if your trailer has any type of side…

view full answer...

Answer 6

I checked Lippert's actual dimensional engineering drawing for this product to verify the dimensions for you. The overall length of this unit is 96 inches end to end. The outside mounting brackets are 1-1/2-inches x 22-1/2-inches. These…

view full answer...

Answer 7

We do have handrails that are going to allow for an easier way for your mom to get up the steps and into your 2016 Heartland Cyclone, the issue with changing from the Lippert SolidStep Manual Fold-Down Steps #LC791574 to a TorkLift GlowStep is the…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

With a ladder on the back of your RV it is unlikely you will still be able to fold up the 24 x 84 etrailer Cargo Carrier for RV Bumpers #e96ZR. Reason why is when the carrier folds up it takes up all the space of the bumper, so unless your bumper…

view full answer...

Answer 12

The 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR can hold a spare tire but there isn't any sort of specific mount for this. The photo attached below is a custom job from a neighbor and I'm not totally sure what they used to create…

view full answer...

Mounts for Cargo Carrier for RV Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching