Replacement Hubs for Older Trailer with a 5 x 4-1/2 Lug Pattern
Question:
I have an old handmade trailer that has 4 lugs on 4” hubs. I would like to replace hubs with 5 lug x 4.5” dia hubs. The wheels are 13”. The spindles and hubs have a 1.25” dia seal ID and 1.000” dia x 4.125” long shaft for bearings. Bearings: Timken L44643 Seal: National 441319 Which hubs will allow this? I can send a sketch with dimensions if you need them. Thanks
asked by: Matthew R
Expert Reply:
Thanks for the dimensions and bearing numbers! Based on how specific you were I do not need a sketch. We have a couple of options for you depending on what kind of finish you are looking for.
For a standard finish you will want the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 item # 8-258BTUC1. These are sold individually and come with lug nuts and all bearings and seals required for installation.
For a galvanized finish that offers more protection you will need the Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized item # AKIHUB-545-2-G-1K. These are also sold individually and come with lug nuts and all bearings and seals required for installation.
Don't forget your bearing grease. I recommend the Prime Guard Wheel Bearing Hi-Temp Red Grease item # L11380.
Products Referenced in This Question
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Hub
- Standard
- L44643
- L44643
- For 2000 lbs Axles
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Standard
- L44643
- L44643
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
LubriMatic Prime Guard High Temperature Wheel Bearing Grease - Red - 16-oz Can
- Lubricants Sealants Adhesives
- Grease
- Brake and Bearing Grease
- Lithium Complex-Based
- Standard Bearing Grease
- Polyurea - Conventional
- 16 oz
- LubriMatic
more information >
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Trailer Hub for the TDE 46205 with Galvanized Finish
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Article: How to Tell the Weight Rating of a Trailer Axle
- Q&A: Replacement Bearing Solution for DICO Hub 45263
- Article: How to Measure a Trailer Axle
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Can I Swap Out 4-Lug Hubs For 5-Lug Hubs On A Little Dude Boat Trailer?
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Q&A: Replacement Hub/Drum for Triton Axle 08353
- Q&A: Replacement Hubs with L44649 Bearings on Snowmobile Trailer
- Article: Trailer Tire Sizing
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)