Will The Blaylock EZ Jack And Wheel Chock Work With Tandem-Axle Boat Trailers

Question

Question:

I am considering your aluminum EZ Jack product for my boat trailer. The trailer is a tandem axle, boat is 22ft Skeeter bass boat trailer about 24ft long, tires are 245/45 R18s. Would this product give me enough height to change a tire?

asked by: Peter W

0

Expert Reply:

Yes, the Blaylock EZ Jack and Wheel Chock for Tandem-Axle Trailers, # EZ-JACK will work wonderfully for the boat trailer you describe.

expert reply by: Michael R

0

Answer 1

The Andersen Rapid Jack #AM3620 is not designed to work with triple axle trailers. If you are looking to use it for leveling, then I recommend the Andersen Camper Wheel Chock and Leveler #AM3604 for your application. The similar #EZ-JACK is also not…

view full answer...

Answer 2

I spoke with my contact at EZ-Jack and he says that to use the EZ-Jack on a triple axle trailer you will need to turn the curve up, opposite the wheel, and drive up on the jack and you will be able to change the tires. Other wise a floor jack and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The best way to identify the seal needed, is to get the number that is stamped or imprinted on the seal. You may have to remove the seal in order to see the numbers. If you cannot find the number on the seal, if you can find the numbers on the inner…

view full answer...

Answer 5

The best option we can offer you is the Trailer Idler Hub Assembly part #AKIHUB-545-2-EZ-2K which will be a direct replacement for the Dico Trailer Hub Assembly part 45263 so long as you the Double Lip Grease Seals part #RG06-010. The Trailer Idler…

view full answer...

Answer 6

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 7

The puck feet on the Gen-Y Hitch Gooseneck Trailer Hitch for Dodge Ram OEM Puck Systems #GY83XR is just to help stabilize the ball mount and does not lock into place in the puck. The locking mechanism on top will lock the shank into the gooseneck…

view full answer...

Answer 8

The Powerbuilt Unijack #ALL620470 referenced in your question has a weight capacity of 4,000 pounds. This is likely enough for your 8,200 pound trailer, but I recommend going up a bit with the Unijack #ALL620471 that is rated for 6,000 pounds. This…

view full answer...

Answer 9

The Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs #LC333966 has a total lift of 37 inches so you can simply add that to the pictured dimensions for the fully extended lift. The Atwood name on the picture is because…

view full answer...

Answer 10

It is not recommend to jack up a trailer by the axle. This may cause damage to the axle itself. It also puts too much stress on the leaf springs. Instead, you will want to place the jack under part of the trailer frame preferably next to the leaf…

view full answer...

Will The Blaylock EZ Jack And Wheel Chock Work With Tandem-Axle Boat Trailers

Product Page this Question was Asked From

Continue Researching