Hole Spacing Of The JR Products Locking Camper Door Latch # 37211685

Question

Question:

What is the hole spacing required between the two screws?

asked by: Jim K

0

Expert Reply:

The holes of the Locking Camper Door Latch # 37211685 from center-to-center are 1-11/16".

expert reply by: Kevin C

0

37211685 Hole Spacing
(click to enlarge)

Answer 1

The Privacy Latch for RV Screen Door - Gold Item #37220515 doesn't actually lock. What you'll want instead is the Locking Camper Door Latch - White Item #37211685 which will lock and will come with 2 keys.

view full answer...

Answer 2

To replace your Atwood/Dometic G6A-8E water heater I recommend the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door Item #FR98SR. It has similar dimensions at 12-5/8L x 12-13/16W x 19-3/16D so…

view full answer...

Answer 3

I spoke with my contact at B&W and it sounds like you have a bind. If you have a lube plate that is thick on your kingpin, or maybe too high holding pressure on the jaws, your jaws may not physically open even though the handle is in the open…

view full answer...

Answer 4

It sounds like you have a Heng's Roof Vent 122112. This is known as the Ventline Old Style Rounded Dome Trailer Roof Vent. Replacement parts are, #BV0554-01 for white or, #BV0554-03 for black. This will be the continuous hinge style. Please…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Hole Spacing Of The JR Products Locking Camper Door Latch # 37211685

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching