Availability of Longer Snapper Pin that is 5/16 inch in Diameter

Question

Question:

Need a coupler pin for this trailer It needs a wide pin length and a deep box retainer to clear the coupler

asked by: Thomas G

0

Expert Reply:

I am not sure what length you need but the part # 37201244 that you referenced is our longest snapper pin with a 5/16 inch diameter as it has a usable span of 2-9/16 inches.

expert reply by: Jameson C

0

Answer 1

The VIN doesn't give me really any information beyond what you already gave so I reached out to the manufacturer. You have the 3,700 lb axle, but it has the standard 3,500 lb spindle size based on the bearing numbers they gave me for your axle. I…

view full answer...

Answer 2

Thanks for the picture of the coupler of your rental trailer. Based on that we know it's a Demco EZ latch so for a lock that will work great securing it to your hitch ball we know the etrailer coupler lock part #e98887 would work well. It fits…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Availability of Longer Snapper Pin that is 5/16 inch in Diameter

Product Page this Question was Asked From

Continue Researching