Replacement Tarp and Headers for Truxedo TruXport Soft Tonneau TX281101

Question

Question:

Does the plastic rails on the head and tail of the tarp come with it or I have to buy them separately? If not, is there trap to buy with the plastic rails installed on it?

asked by: Rad

0

Expert Reply:

If you are need of the front header and rear header for the # TX281101 you'd need the # TX2811-FrontHeader and the # TX2811-RearHeader for the rear header. Then for the tarp you'd want the # TX281101-CVR and you'd be set.

expert reply by: Jameson C

0

Answer 1

Since you have a 2003 Chevy Silverado 1500 with a 6-1/2 foot bed the correct rear header would actually be the part #TX2811-RearHeader and not the part number you mentioned.

view full answer...

Answer 2

Yes the Replacement Rear Header for Truxedo Truxport Tonneau Cover #TX2722-RearHeader is a kit. This would also work with a Truxport latch kit you have now of #TX1117755.

view full answer...

Answer 3

Since you have a Truxedo TruXport tonneau cover the correct replacement latches would be the part #TX1117755. The cover would have to have been made after 2011 so you'd have to think back to the year you bought the tonneau. If it's older we…

view full answer...

Answer 4

To install replacement latches #TX1117755 you will need to remove the tailgate header rail from the side rails. Then you would remove the one fastener per latch holding the old ones on. Next slide off the old latches, slide the new ones into place,…

view full answer...

Answer 5

The latches do not come with the rail assembly part #TX2459-DS that you referenced. If the cover was made before February of 2011 you would need to replace the cover as there are no longer part, however if they were made after that month you would…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...