Shackle Diameter of BOLT Covered Padlock

Question

Question:

What is the diameter of the shackle? I want to use it on a 1/4inch opening

asked by: Gary

1

Helpful Expert Reply:

The shackle diameter of the Bolt lock part # BLT59FR is 5/16 inch. The # 605DAT has a 1/4 inch diameter though.

expert reply by: Jameson C

1

Answer 1

We have the MasterLock Trigger Style Coupler Lock part #605DAT which has a span of 3/4 inches like you said you need that would work well. You are correct and the tighter the latch opening is to the trigger latch of the coupler the harder it would be…

view full answer...

Answer 2

We sure can, but the Master Lock #605DAT lock you'd looked at isn't available keyed alike. We do have options for keyed alike coupler locks, however. I'd recommend a latch lock such as the etrailer brand #e98890 for a 7/8 inch span or…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

I spoke to Demco about the Demco Autoslide Locking Plate for Lippert Rhino Pin Boxes part #DM76FR, the side plates are supposed to be angled as that's what provides the clamping force. I would just make sure you have the bolts torqued fully to…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Shackle Diameter of BOLT Covered Padlock

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching