Manual Tail Gate Lock for a 2013 Toyota Tacoma with Rear Backup Camera

Question

Question:

I want a manual lock to lock the tailgate handle for my 2013 Toyota Tacoma with backup camera.

asked by: Sam L

0

Expert Reply:

For a manual tail gate lock for your 2013 Toyota Tacoma with the backup camera you can use # PAL5400. I have included a picture that shows where the camera will mount on the new lock. I have also included a link to a video review of this lock for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

According to Pop and Lock, the back-up camera in your 2010 Tacoma is indeed compatible with the #PAL5500 locking tailgate handle. There will be enough slack in the wiring to move the camera from its existing location on the OE tailgate handle to…

view full answer...

Answer 2

I checked directly with Pop & Lock for tailgate power lock kits for your 2004 Toyota Tacoma and their kit #PAL8510 is a fit for your truck. This power lock works with your factory power lock system, so it locks and unlocks using remote…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

The Rhino Rack ROC25 part #RR46XR has a 165 lb dynamic weight capacity which means that's how much it can carry while travelling and incurring the standard bumps and movement that creates. While Rhino Rack doesn't give a static weight…

view full answer...

Answer 9

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to…

view full answer...

Answer 10

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The manual switch for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover #PE44CV can be found as part #311-BL-1120 on our site. This plugs into the harness at the canister and then you route and install the switch wherever it works best for…

view full answer...

Manual Tail Gate Lock for a 2013 Toyota Tacoma with Rear Backup Camera

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching