Axle Hub That Uses Bearings JM511946 and JM205149, Race JM511910 and JM205110

Question

Question:

Im looking for the 10,000 lb axle hub that fits bearings JM511946 2.5 ID JM205149 1.96 ID Races JM511910 JM205110

asked by: Miles M

0

Expert Reply:

The Kodiak Disc Brake Kit # K2HR12A11-120DW is the only hub we have that uses the Inner Bearing # TRJM511946, Outer Bearing # JM205149, Inner Race # TRJM511910, and Outer Race # JM205110. Those bearings are what fits with an ALKO axles using #120 spindles.

If that hub is what you are looking for you will need to purchase the Bearings # TRJM511946 and # JM205149 separately along with a Oil Seal # 10-56 for each hub.

expert reply by: Bud M

0

Answer 1

For a 10k AL-KO trailer axle we have the Kodiak Disc Brake Kit part #K2HR10A11RERR but the #K2HR12A11-120DW that you referenced is designed for a 12k AL-KO axle.

view full answer...

Answer 2

The trailer hub part #K2HR12A11-120DW fits a 120 spindle which uses the bearings #JM205149 and #TRJM511946.

view full answer...

Answer 3

Thanks for reaching out! In order to replace the bearings and seal for your 12K hub assembly you'll need to piece the following parts together as we currently (December 2022) don't have a whole bearing kit that includes all of the parts…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Axle Hub That Uses Bearings JM511946 and JM205149, Race JM511910 and JM205110

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching