What Size Wrench is Used to Tighten the Anti-Rattle Device and Lock, # 63232

Question

Question:

What size is the includex wrench? I dont have the product in hand yet, but I wanted to see if I have a box wrench or socket that will fit. Thanks.

asked by: Dave G

0

Expert Reply:

I went out to the warehouse and pulled an Anti-Rattle Device and Lock, # 63232. I measured the span of the included wrench and it is 5/8 inches. Any 5/8 inch wrench or socket can be used in place of the flat wrench that is included. I have linked a video review of this device for you.

expert reply by: Michael H

0

Answer 1

To install the Anti-Rattle Trailer Hitch Receiver Lock #63232 that you referenced you will need to first thread the bolt portion of the device into the hitch, lock it, and then finally tighten the bolt head of the device. Just getting the device…

view full answer...

Answer 2

Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" Item #C31018 has a 500 pound vertical load limited so the 389 pounds combined for the motorcycle and the carrier is within that capacity.

view full answer...

Answer 3

Trailer hitch installation on your 2016 Mazda CX-5 will require basic hand tools like a 3/4-inch socket and ratchet, and also a torque wrench like #ALL944001. The linked instructions tell you all the tools required to mount Class III Hitch #76138…

view full answer...

Answer 4

I checked with Curt and the side plates of the Curt front hitch part #C31018 are 12 inches tall.

view full answer...

Answer 5

There are bound to be some slight differences amongst the year vehicles that Curt front receiver #C31018 fits. The truck in the video, linked for reference, is a 2012 so there have been some design changes between then and the 2015 models. But the…

view full answer...

Answer 6

If you know the reference number that was printed on the key, we might be able to obtain a replacement key. If you don't know the key number, you best bet would be to drill the lock cylinder out, or use a cut-off wheel on an angle grinder to cut…

view full answer...

Answer 7

Curt front-mount hitch #C31018 and Westin Sportsman Grille Guard #40-2375 are both confirmed fits for your 2013 Ford F-250 SRW 4X4. Unfortunately, both require the same mounting points on the truck's frame so both cannot be installed at the same…

view full answer...

Answer 8

Make sure that when you put the locking portion on the pin that it isn't already locked. I have done that before.You will know that the unit is locked if you can pull the key out. When unlocked the key cannot come out. Make sure that the pin is…

view full answer...

Answer 9

You are correct there is a weight advantage for aluminum, item #C18100, over steel, item #CC-100, but the biggest reason aluminum is considered over steel, for most of our customers, is corrosion resistance and appearance. You do not need to upkeep…

view full answer...

Answer 10

I went out to our demo studio to measure the tubing used on the Pro Series cargo carrier #63153. The tubing is 3/4 inch square. I hope this size is going to work for you and the light strip you plan to use.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Size Wrench is Used to Tighten the Anti-Rattle Device and Lock, # 63232

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching