How Can I Mount A Buyers Products 50 Ton Pintle Hook To Class 8 Semi

Question

Question:

Hello, I just purchased this product and was wondering what Buyers Products mounting plate would be a good fit. its going on a clase 8 semi. Thank you. Buyers Products P45AC6K 45 Ton Air Compensated Pintle Hook, 6-Hole Mount With Brake Chamber Bracket

asked by: Nour E

0

Expert Reply:

If you have the mounting area on the back of your semi, my recommendation is the Buyers Products Air Chamber And Plunger Kit For PH50/PH55 Series, part # 337PH50ACMK. This plunger will use your trucks air brake system.

I have included a product description link and video review links below.

expert reply by: Mark Smith

0

Answer 1

I have attached a photo of the Tow Ready Pintle Hook Mount, part #63059 with several measurements noted. As the photo shows, the length of the shank from the end to the front face of the plate is 14-5/8 inches. The plate is 5/8 inches thick so the…

view full answer...

Answer 2

The Buyers Products 10 Ton Combination Hitch with Mounting Kit #33710057 has hole diameters of 5/8 inches. They are spaced 3-3/8 inches and 1-3/4 inches on center. I've attached a photo to assist as well as a video.

view full answer...

Answer 3

I went out to our warehouse and measured the Buyers Products Air Chamber and Plunger Kit #337PH50ACMK you were looking at. The bolt hole spacing on the mounting bracket measures 5-3/4" center to center, and the ovals measure 1-1/2" long.…

view full answer...

Answer 4

The mounting holes for the Buyers Products 45 Ton 6-Hole Air Compensated Pintle Hook #337P45AC6 are spread 5" apart horizontally. The bottom 2 holes are spread 2-1/8" vertically while the top 2 holes are spread 2-3/8" vertically. I…

view full answer...

Answer 5

The Buyers Products Fabricators Hitch Plate #3371809027A will work with the 40,000 pound Pintle Hook #33710042. This will be the highest capacity pintle that can be used in unison. Both the #337PH50 and #337PH55 have odd bolt hole spacing and will…

view full answer...

Answer 6

I do not have a cut sheet for Buyers 10-hole pintle hook part #337PH55 but the mounting hole diameter measures 0.812". The bottom mounting holes measure 1.062 inches center to center. From the center of the third mounting hole to the center of…

view full answer...

Answer 7

I spoke with Buyers Products, and they actually don't sell the block part of the Buyers Products Air Chamber And Plunger Kit For PH50/PH55 Series #337PH50ACMK separately. The block is part of #337PH50ACMK, so if you needed a replacement,…

view full answer...

Answer 8

The mounting holes on the Buyers Products 50 Ton Air Compensated Pintle Hook #337PH50AC are 0.781" in diameter. The horizontal mounting holes are 5" apart center on center, and the vertical mounting holes are 2.375" at the top and…

view full answer...

Answer 9

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...