Correct 4-Lug Trailer Hub for StarCraft Trailer with 2,000 Lb Axle

Question

Question:

Hello I was looking for replacement hub assembly for my 92 StarCraft stardust axle weight 2000 . 4lug I want to make sure I get the right size inside hub isee numbers 8-173 nd 276 0 I want to make sure I buy the right size any advice?

asked by: Maria B

0

Expert Reply:

For a trailer with 2,000 lb axle and 4-lug hubs you'll want to use the Trailer Idler Hub Assembly for 2,000-lb Axles part # CE13110. This is a complete hub with bearings, seal, lug nuts, and grease cap. The hub is also pre-greased so there is no mess.

expert reply by: Conner L

0

Answer 1

The standard hub for a 10" wheel and 4 on 4" lug pattern is going to either have #L44643 bearings and a 1" diameter spindle, or an #L44649 bearing and a 1.063" spindle. Once you've determined which one you have then you'll…

view full answer...

Answer 2

We've had previous customers with a Starcraft 1701 pop up like yours tell us that their tire size was 4.80-12 mounted on a wheel with a 4 on 4 inch bolt pattern. If that's what you have then you'd want the #AM30620 which matches both the…

view full answer...

Answer 3

The correct replacement idler hub for a 1998 Starcraft Stardust Popup Camper with Dexter 2,200 Lb Axles is the Trailer Idler Hub Assembly part #AKIHUB-545-2-2K.

view full answer...

Answer 4

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Correct 4-Lug Trailer Hub for StarCraft Trailer with 2,000 Lb Axle

Product Page this Question was Asked From

Continue Researching