Are the Timbren 1" Spacers For Raised Frame Vehicles Sold In Pairs

Question

Question:

are these sold as a pair ?

asked by: Keith B

0

Expert Reply:

The Timbren 1" Spacer For Raised Frame Vehicles part # A25723-90AH00 are sold individually, you'll simply need to order one for each side or multiples depending on the lift. They are also offered in a 1/2" version as part # TA25722-90P00. You'll want the space between the spring and strike plate/axle to be about 1/2"-1-1/2".

expert reply by: Conner L

0

Answer 1

The ideal gap between the bottom of the jounce bumper and top of the contact point is about 1/2"-1" but you can go more if you don't want them to engage as soon or as often. Therefore, in lifted applications you'll need to use…

view full answer...

Answer 2

To add a 1" spacer #A25723-90AH00 to the Timbren Active Off-Road Bumpstops #TABSOSR you were looking at for your 2014 Toyota Tundra you will need to purchase two grade 5 or 8 3/8" x 2-1/2" F/T UNC bolts from your local hardware store.…

view full answer...

Answer 3

For a lift spacer that fits a Timbren kit for your 2020 GMC Sierra like the #TGMRCK25D you'd need a spacer with a 3/8 inch diameter hole like the #A25723-90AH00.

view full answer...

Answer 4

I have another option for you, but the Timbren Active Off-Road Bumpstops - Rear Suspension - 3,000 lbs #T86FR you were looking at for your 2020 Jeep Gladiator is not designed to prevent sag from towing a trailer, but instead is designed to give you…

view full answer...

Answer 5

It is permissible to stack two 1-inch spacers #A25723-90AH00 to give you a total of 2-inches of height adjustment for your Timbren rear axle kit. Rear axle jounce spring kits like those from Timbren are intended primarily for use with supporting…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...

Answer 11

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Are the Timbren 1" Spacers For Raised Frame Vehicles Sold In Pairs

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching