Which Timbren Spacer Bolt Diameter for Timbren Kit that Fits 2020 GMC Sierra 2500

Question

Question:

I have a set of timber gmett35ds on my 2020 GMC 2500HD. I need to add lift spacers. What bushing diameter do I need?

asked by: Alan V

0

Expert Reply:

For a lift spacer that fits a Timbren kit for your 2020 GMC Sierra like the # TGMRCK25D you'd need a spacer with a 3/8 inch diameter hole like the # A25723-90AH00.

expert reply by: Jameson C

0

Answer 1

The ideal gap between the bottom of the jounce bumper and top of the contact point is about 1/2"-1" but you can go more if you don't want them to engage as soon or as often. Therefore, in lifted applications you'll…

view full answer...

Answer 2

To add a 1" spacer #A25723-90AH00 to the Timbren Active Off-Road Bumpstops #TABSOSR you were looking at for your 2014 Toyota Tundra you will need to purchase two grade 5 or 8 3/8" x 2-1/2" F/T UNC bolts from your local…

view full answer...

Answer 3

The Timbren 1" Spacer For Raised Frame Vehicles part #A25723-90AH00 are sold individually, you'll simply need to order one for each side or multiples depending on the lift. They are also offered in a 1/2" version as part…

view full answer...

Answer 4

It is permissible to stack two 1-inch spacers #A25723-90AH00 to give you a total of 2-inches of height adjustment for your Timbren rear axle kit. Rear axle jounce spring kits like those from Timbren are intended primarily for use with supporting…

view full answer...

Answer 5

For a heavy duty Timbren confirmed as a fit for your 2015 Chevy Silverado 2500HD we have the part #TGMRTT35D as a confirmed fit. This would be your best option. Now it sounds like your lift is a body lift which does not change the suspension in any…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Which Timbren Spacer Bolt Diameter for Timbren Kit that Fits 2020 GMC Sierra 2500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching