Availability of Replacement Parts for Curt C16550 R20 5th Wheel Hitch Slider Assembly

Question

Question:

I have a curt a20 ram roller hitch and I’m looking to replace just the plates the rollers roll on. Are these parts available!

asked by: Ron

1

Helpful Expert Reply:

I contacted my Curt representative, and found that Curt doesn't offer component parts for their R20 roller assembly.

If you have something that needs replacing, you'll need to replace the entire roller assembly which is part # C16550. The good news is that the R20 roller is covered by a 10 year warranty, so I'd first contact whomever you purchased it from to see if you can get a warranty replacement.

expert reply by: Mike L

1

Answer 1

Chucking will be reduced by switching from the Curt R16 to the Curt S20 Slider for E16, A16, and A20 5th Wheel Trailer Hitches #C63DR. I'm not 100 percent sure what type of verification you were referring to specifically, but I can tell you…

view full answer...

Answer 2

Sounds like you are trying to switch up your fifth wheel hitch setup so that you have more turning clearance. Whether you use a fifth wheel rail kit or a gooseneck adapter the center of the hitch's jaws are going to be right above the center of…

view full answer...

Answer 3

The bolt pattern differs between the Curt Q20 #C16130 and Curt R16 slider #C16560 so they would not be a compatible match. The Q20 requires the Curt R20 slider #C16550 in order to transition to a sliding 5th wheel hitch.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 9

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 10

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Availability of Replacement Parts for Curt C16550 R20 5th Wheel Hitch Slider Assembly

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching