Correct Snap Pads for Newmar Canyon Star Motorhome

Question

Question:

Snap Pad. I have a 2016 Newmar Canyon Star with Equalizer leveling system. Which Snap Pad will fit my coach?

asked by: Prose T

0

Expert Reply:

I recommend measuring the feet on your leveling system and noting the shape of the pad. That said, it should be 9" round pads and in which case you would use the SnapPad XTRA Jack Pads for Lippert Leveling Systems part # SP54FR4.

If you have a different size/shape you can select this from the list below.

expert reply by: Conner L

0

Answer 1

We do carry the 9" SnapPad Jack Stand Pads in a 6-pack as part #SP54FR6!

view full answer...

Answer 2

For your application you'll likely need the SnapPad Jack Pads for Class A and C Motorhomes w/ 9" Round Jack Feet #SP54FR2 since your 2022 Jayco 30Z motorhome is a Class C. We don't have a fit list though so you'll…

view full answer...

Answer 3

The covers for your EZ4 Base Plate #RM-523182-4 are the Roadmaster EZ Base Plate 1-1/2" Receiver Covers #RM-210. I confirmed this fit with my contact at Roadmaster.

view full answer...

Answer 4

The Curt T-Connector Vehicle Trailer 4-Pole Wiring Harness #C55372 that you referenced is a correct fit for your 2003 Chevrolet Tracker. This 4-pole trailer harness installs by simply plugging in to a connection point in the rear cargo area of your…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Correct Snap Pads for Newmar Canyon Star Motorhome

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching