How Long Are The Arms On The Roadmaster Falcon 2 Tow Bar

Question

Question:

What diameter and length are the twist arms?

asked by: OJM

1

Helpful Expert Reply:

The telescopic arms on the Roadmaster Falcon 2 Tow Bar - Motorhome Mount - 2" Hitch - 6,000 lbs # RM-520 are 1 inch wide. They will extend out 16 inches and are a total of 35-1/2 inches long when fully extended.

They are very easy to extend and retract. I had no issue when handling the unit, you just push a button and it will release for you to collapse it.

expert reply by: David B

1

Answer 1

There are some great options for baseplates for a Honda CR-V, but the Roadmaster Direct-Connect #RM-521448-5 is made specifically for use with a Jeep Wrangler. If you have a 2007-2011 CR-V, go with #RM-521559-5. If you have a 2012-2014, use…

view full answer...

Answer 2

According to Roadmaster, their #RM-521567-5 direct-connect base plates are compatible with your Falcon 5250 tow bar. Compared to the #RM-521567-4 which requires a crossbar, the #RM-521567-5 makes for a cleaner install that's easier to use. To…

view full answer...

Answer 3

The Roadmaster Direct-Connect Base Plate Kit - Removable Arms #RM-521448-5 are a confirmed fit for your 2014 Jeep Wrangler Rubicon and should fit just fine with your Falcon 5250 tow bar. I reached out to my tech contact at Roadmaster and there are…

view full answer...

Answer 4

I have a solution for you, however, the Demco #DM9518320 baseplate kit you were checking out is only compatible with the 75th Anniversary or Rubicon Hard Rock Edition. The Roadmaster EZ5 Direct-Connect Base Plate Kit #RM-521448-5 is the most…

view full answer...

Answer 5

The Roadmaster Direct-Connect Base Plate Kit part #RM-521453-5 which is a fit for a 2019 Jeep Wrangler Unlimited will work with the Roadmaster Falcon 2 Tow Bar part #RM-520. That said, you would not use the crossbar with quick-disconnects. The tow…

view full answer...

Answer 6

I attached an exploded diagram that shows how the Roadmaster Base Plate kit part #RM-520 will bolt together. I also attached a set of installation instructions that should help you figure it all out as well.

view full answer...

Answer 7

The tools needed to replace the inner arm of your Roadmaster Falcon Tow Bar part #RM-520 would be a 9/16 socket wrench, 1/4 inch allen wrench and a slot screwdriver. I attached picture of the installation instructions for this kit for you to check…

view full answer...

Answer 8

According to Roadmaster, any Sterling tow bar with a serial number under 14,500 does not have a replacement inner arm available and you will need a new tow bar. There are great options available and our most popular is the Roadmaster Falcon 2…

view full answer...

Answer 9

I attached a couple picture that show where the white spacer should be on your Falcon 2 part #RM-520 when using the rebuild kit #RM-910003-60. Looks like the white spacer goes on the very bottom.

view full answer...

Answer 10

The crossbar style of Roadmaster base plate kits like the part #RM-521567-4 do not actually come with a crossbar but instead attach to tow bars that have crossbars like the Roadmaster Falcon 2 part #RM-520. Or if you prefer not to use the crossbar…

view full answer...

Answer 11

Thanks for your picture, it helped out a lot. As long as your 2013 Honda CR-V doesn't have a brush guard the Roadmaster EZ5 Base Plate Kit #RM-521567-5 will the right base plate kit for you. It's important to note that safety chain anchor…

view full answer...

Answer 12

The base plate #3141-1 that you referenced does not fit a 2014 Honda CR-V so you'll need to start over with a new flat towing setup. For a base plate kit you'll want the part #RM-521567-5. In addition to the base plates, you will also need a…

view full answer...

How Long Are The Arms On The Roadmaster Falcon 2 Tow Bar

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching