How Far Above Roof Does Ventadome Trailer Roof Vent # V2110SP-24 Extend When Installed

Question

Question:

how far does it project above vehicle roof? or add to total vehicle height? have almost no clearance between my vehicle roof and garage door opening. thank you.

asked by: John S

0

Expert Reply:

The Ventline Ventadome Manual Trailer Roof Vent, part # V2110SP-24, measures 2-1/4 inches from the top surface of the mounting flange to the top of the closed vent lid. When mounted to the top of your trailer roof it will extend above the roof this distance.

I have attached a photo of this item showing the measurement I took. The 2-1/4-inch height was taken
from the top of the steel mounting flange to the raised bumps at the corners, which are the highest points on the lid.

expert reply by: Adam R

0

click to enlarge

Answer 1

For a low profile roof vent for you trailer the part #V2110SP-24 would be a great option. When installed it will only add 2 inches to the height of your trailer. Only issue is that it won't allow light in since the lid is metal. I wish there was…

view full answer...

Answer 2

I walked out to our warehouse and measured the Ventline Ventadome Trailer Roof Vent #V2110SP-24. The height of the vent from the top of the trailer to the top of the vent when closed measured approximately 2-1/4 inches. When the vent is fully opened…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...