Trailer Hitch that Fits 1987 Ford F-150 with 6,000 lb Towing Capacity

Question

Question:

Hello, I have a 1987 F-150. I am looking for a bolt on hitch. Would a 6000 lb hitch. Dont want to have to drill unless it is absolutely necessary. Any help would be appreciated. Thanks

asked by: Mike K

0

Expert Reply:

Due to the frame design of your 1987 Ford F-150 all hitch fits would require frame drilling since there aren't holes present on the frame. We do have great 6k rated hitches that fit your truck like the # 41004 though. This fits whether you have the standard or step bumper.

expert reply by: Jameson C

0

Answer 1

If your 1993 Ford F-350 has a factory 7-way installed you could use an under-dash install harness like the part #C51312 to install a controller like the Curt Discovery part #C51120. The harness would be under the dash taped to another harness near…

view full answer...

Answer 2

All you need to install the Hayes Syncronizer part #HA81725 in your 2017 Ford F-150 is the custom install harness part #HA81794-HBC which plugs in under the truck dash and you'd be set.

view full answer...

Answer 3

Yes, the red light on the Hayes Syncronizer Trailer Brake Controller #HA81725 will come on whenever you apply your tow vehicle's brakes, even when no trailer is connected. However, no power is used when there isn't a trailer…

view full answer...

Answer 4

I went out to measure both Draw-Tite Trailer Hitches, #41904 and #41004. They will not use the same mounting locations. On #41904, the center to center distance between the two closest bolt holes is 4-3/4 inches. Between the center bolt hole and the…

view full answer...

Answer 5

I've checked the hitches and while none of them actually come inside of the frame rails the Draw-Tite Max-E-Loader Trailer Hitch Receiver part #41004 will offer the most clearance of the three options you have mentioned.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Trailer Hitch that Fits 1987 Ford F-150 with 6,000 lb Towing Capacity

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching