Recessed 28 inch x 16 inch Rectangular Boat Table

Question

Question:

i want the flush mount for this rectangular table. where do i get that

asked by: Julie R

0

Expert Reply:

The flush mount version of the Rectangular Boat Table # 315-DSH-KS that you referenced is actually part # 315-DSH-KF on our site so that's what you'll want to order instead.

Attached is a review video for you to check out.

expert reply by: Jon G

0

Answer 1

The Rectangular Boat Table #315-DSH-KF can be put up and taken down each time. The only thing that gets bolted down is the flush-mount bracket that the pole goes into on the boat floor. The actual table post is pushed into the flush-mount and the top…

view full answer...

Answer 2

The Rectangular Boat Table - Surface Mount - 28" x 16" #315-DSH-KS has an ivory color so it's an off-white but not quite cream-colored. The base that comes with it is installed by putting mounting screws through the base into the floor…

view full answer...

Answer 3

The Table Leg #315-DTX that comes with the Rectangular Boat Table #315-DSH-KF is 2" OD. The ends of the tube are tapered down to 1-7/8" OD for the Mounting Brackets #315-DTY and #JIF54FR.

view full answer...

Answer 4

According to Jif Marine, when selecting hardware for installation of the #315-DSI-KS you need to choose a fastener based on the type of material that the table will be mounted to. They recommend a machine fastener like a 1/4 X 20 stainless steel bolt…

view full answer...

Answer 5

For a replacement 7-Way for your 2001 Ford Expedition you can use #74682 that you have referenced. You will just need to unplug the old 7-Way at the back. In your picture the grey plastic part on the connector is a sort of lock that needs to be…

view full answer...

Answer 6

The part #HM40975 normally would plug right in to the 7-way wiring of your 2005 Ford F-250, but if for some reason you have a totally hardwired setup your other solution would be to use the part #HM40975-11998 which would allow you to hardwire the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Recessed 28 inch x 16 inch Rectangular Boat Table

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching