Replacement Diverter Valve for a Phoenix Faucets System

Question

Question:

Do you have the center diverter valve also that goes with the Phoenix stems

asked by: Dave B

0

Expert Reply:

Given the product you asked this from (Replacement Compression Stems for Phoenix Faucets 3 Valve Tub and Shower Faucets # PF99FR) I believe the Replacement Diverter Stem for Phoenix Faucets 3 Valve Tub and Shower Faucets # PF49FR is the diverter stem valve you are needing.

If this is not what you are needing, please reach back out to me with information on your faucet and I would be happy to assist you further.

expert reply by: Scott S

0

Answer 1

I would be happy to help! The correct Replacement Compression Stem will be dependent on the style of your shower faucet. If you have a faucet with lever handles you will need the #PF187023 for the cold side and #PF187020 for the hot side. If you have…

view full answer...

Answer 2

Thanks for reaching out, I looked into it and found out. **Phoenix Faucets Hybrid RV Bathroom Faucet - Dual Lever Handle - Chrome #PF232301. *Replacement Compression Stem for Phoenix Faucets Dual Handle Kitchen or Bathroom Faucets - Qty 1 #PF187021.…

view full answer...

Answer 3

The correct handle that fits with the Replacement Diverter Stem w/ Brass Bonnett #PF183001 is the Replacement Diverter Knob #PH22GR which comes with the screw and cap to get it installed.

view full answer...

Answer 4

The part #PF187021 is the cold side stem and bonnet and the part #PF187022 is the hot side.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Diverter Valve for a Phoenix Faucets System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching